The first unit intelligent washing machines from Fisher & Paykel was discontinued in 1991 and since then we have had 8 improved and more sophisticated models. Although very different, the most common errors are very similar. From our experience we can say that almost 80% of them are small errors, but it's worth repairing. We will try all of them.If you will find that your cover different, there may be a combination to be covered by few.
NO POWER
ThisEngine, pump, rotor position sensor, reed, or a display of water valves: a failure the error can be caused major electrical components. It can also be also in motor control. Can be burned by water or by voltage spikes associated abbreviation.
On the control "Phase 4" (models 085, 058, 508, 608, 708) motor, there is a mode where you can stop in case of a transient on the power. This means this machine is in "sleep" mode and go tothe form does not restart when power is off the wall for at least 90 seconds.
Having regard to the "Stage 5" (095-Fresh models, 059 Pride, Excellence 509, 609, 709) as part of the pump power. If it is unplugged (activated protection from overheating, which can be caused by a blockage of the pump) machine will be dead.
Repair of this defect is quite expensive and vary between models from $ 100 to $ 250
The best way to prevent it is regular low-cost service to perform inspectionsall the important parts and empty pockets before washing. If you purchase used washing machine trying to arrange cleaning, sandblasting and water disinfection, which can lead drum free and dishes all the dirt, blocking the pump.
LOSSES
This is the most common problems of washing machine and in some cases, it's for real technical problems, sometimes related to abuse or incorrect installation.
Easy to see leaks from faucets, water pipes, valves for hot and cold water, the water in the mixing chamber.Loss is from the top of the exhaust pipe is too easy to remember and always on site close to connecting with the body of the machine.
Losses from the pump is almost always caused by poorly protected lanterns; pump
Diaphragm pump and ultimate causes for the loss. Next vanishing point can be air bell.
If the water level is not right and put on high water mark will be padded on the shaker may cause splashing, some "leakage". Capture can be caused by bad (dirty or perforated)Line pressure. The overload can dress the same problem.
Ring neck broken and damaged plastic containers inside are another possible reason for losses and detergent is used too much.
Fixing the problems of loss should not (with the exception of damaged inner shell and the main seal leak) can be very expensive, up to $ 100 at most.
A washing machine is noisy
The noise can be related to different sources, some of which indicate that the machines must be serviced or repaired to avoid moreDamage.
When washing machine is very noisy when running main seal and the bearings are bad. This error must be corrected urgently, this can cause loss of water damage to the motor and the rotor position sensor.
Sound beat is usually associated drain pipe inlet, power cable or dish. Or is loose or washing machine level properly. This can cause other major problems, but it could be annoying.
Another sound may be affected by internal and external causes haveBowl, beat the machine body.
The reason that somehow escaped the water balance of two rings in the inner shell. The same problem can be caused by overloading or irregularly clothes in the pot.
The pump can be very annoying source of noise. This noise starts at the beginning of the spray / rinse or spin deep and lasts until the pump empties. It 'been caused by rusty pump stator (water or moisture damage) or the middle position of the rotor. CRC spray solve the problemtemporary and expensive new pump of machine breakdown (burned on the fire pump controller triac motor) to save.
In addition, broken or chipped rotor magnets may be some grinding noise.
To solve this noise problem, you can expect anything between $ 50 to $ 350
A washing machine is "doing nothing"
Cause of this error can in Reed (cover and off balance). Switch must be replaced to avoid breaking the control engine failure.
Faucets can be the cause of thisProblem also. The water must be connected and valves must be turned on.
If start is delayed, the Start / Pause button does not respond.
When the level of self has been used Resense machine water level each time the lid is open.
Empty
This problem is the natural law. Normally, the length of the hose is too low. Minimum height should be 850 mm from the ground. Top of the exhaust pipe must be replaced by "U"-shaped guide tube to be no more than two inches from the tip of the guide. If I downloadTube is pushed too far into the floor drain or washing machine is empty (siphon) or water during the filling cycle.
Exhaust pipe intake may also be limited or partial blocking of the pump caused.
0 comments:
Post a Comment